Splave
02-08-2010, 07:00 AM
Assassin sent me his XFX 5770 v1 style gpu for some vmod loving.
Here is the mod, 100k VR (98.6K actual) Pretty tight little spot but no probs
http://www.overclockaholics.com/forums/attachment.php?attachmentid=1456&stc=1&d=1265651493
Here is the actual card, I labeled the read points for ya :thumbsup: bad pic sry
http://www.overclockaholics.com/forums/attachment.php?attachmentid=1459&stc=1&d=1265651690
Pic of the bench setup, with chilled air 21F
http://www.overclockaholics.com/forums/attachment.php?attachmentid=1460&stc=1&d=1265651690
And some results, didnt push to hard. Just wanted to make sure OCP didnt kick on ridiculous low or anything. 1.395V 1100/1400 for 05 and aq3 and again I didnt push for higher or ramp up cpu clocks or anything. (Ram is ftw though ;) ) I was going to vmod the mem as well but I was reading the hynix ram though fast as hell is pretty volatile and there is any easy bios mod if you want to get dangerous!
321k aq3
http://www.overclockaholics.com/forums/attachment.php?attachmentid=1457&stc=1&d=1265651690
30k 05 (slow cpu, same score as 1000/1300) Big pic (http://www.overclockaholics.com/forums/attachment.php?attachmentid=1458&stc=1&d=1265651690)
Assassin I wouldnt go over 1.3-1.35v on stock cooler regular room temp. Chilled air 1.4 was fine probably could have gone a bit higher. Should be able to get it back to you priority USPS in the morning. :clapping:
PS to raise voltage turn the VR clockwise (lowers ohms) counterclockwise will lower voltage (increase ohms) All the way lowered will bring you to 1.117v If i remember right, 1.97k ohms. What would you like it set at when I ship?
Here is the mod, 100k VR (98.6K actual) Pretty tight little spot but no probs
http://www.overclockaholics.com/forums/attachment.php?attachmentid=1456&stc=1&d=1265651493
Here is the actual card, I labeled the read points for ya :thumbsup: bad pic sry
http://www.overclockaholics.com/forums/attachment.php?attachmentid=1459&stc=1&d=1265651690
Pic of the bench setup, with chilled air 21F
http://www.overclockaholics.com/forums/attachment.php?attachmentid=1460&stc=1&d=1265651690
And some results, didnt push to hard. Just wanted to make sure OCP didnt kick on ridiculous low or anything. 1.395V 1100/1400 for 05 and aq3 and again I didnt push for higher or ramp up cpu clocks or anything. (Ram is ftw though ;) ) I was going to vmod the mem as well but I was reading the hynix ram though fast as hell is pretty volatile and there is any easy bios mod if you want to get dangerous!
321k aq3
http://www.overclockaholics.com/forums/attachment.php?attachmentid=1457&stc=1&d=1265651690
30k 05 (slow cpu, same score as 1000/1300) Big pic (http://www.overclockaholics.com/forums/attachment.php?attachmentid=1458&stc=1&d=1265651690)
Assassin I wouldnt go over 1.3-1.35v on stock cooler regular room temp. Chilled air 1.4 was fine probably could have gone a bit higher. Should be able to get it back to you priority USPS in the morning. :clapping:
PS to raise voltage turn the VR clockwise (lowers ohms) counterclockwise will lower voltage (increase ohms) All the way lowered will bring you to 1.117v If i remember right, 1.97k ohms. What would you like it set at when I ship?