Socket 2011 3930K Troubles......

[PhIlLy ChEeSe]

OK guys need some suggestions here, I have the asus RIVE 2011 and Intel 3930K CPU with two 60GB Intel Cherryville SSD'S in a raid 0, with two 7970's and a corsair AX1200PSU and finally 16 GB of 1866 RipjawX memory.

Kinda a long story as I'm not sure what my problem is here, started off I had over clocked the memory with a preset in the bios of the RIVE board. After a while I noticed I was having issue's (BSOD) and upon reboot I realized the memory was under volted while runnig at over 2400 MHz. From this point on the memory was an issue so I would just run it at default with normal voltage, and it seemed OK.
So one day I decided the memory is covered so i'll warranty it witch Gskill did no issues, while my memory was gone I had a pair of cheap ass ram i got with a PSU purchase from egg heads. Its an 8 GB kit of Vulcan 1600 memory, so only two sticks in the RIVE. I read the manual on witch slots to use, install and rebooted to adjust the settings everything was fine. Then I thought this is free memory so I cranked it up to around 1866 and upped the voltage and boom I lost the boot sector on my raid. So I killed the power and removed the cheap memory thinking ill be ok when the new Gksills get here. Upon return i installed and still no boot sector, so ok i got to lose what was on them. I deleted the raid then rebuilt it, and now it wont see my damm CD drive so I can install the drivers for a raid?
Did I kill the memory controller on the CPU, or the board, the memory is brand new so I assume it is ok. I was thinking of re seating my CPU then in bios set the defaults n see what happens..............

Suggestions :ohcrap:

cleared CMOS no changes tried switching the Intel SSD'S to the other controller, cant see the damn CD player? ugh!!!!!! HELP!!!:blush:

[ThreeDhero]

I had an issue like this with an MSI board after to use powered down incorrectly. My issue was more with the pci-e bus. I had to reseat the CPU and let it sit for awhile without power plugged in. After putting everything back it powered fine with no issues.
But its odd that you you are having issues with your raid. Might just try breaking everything down and start with the basics.

[PhIlLy ChEeSe]

I had an issue like this with an MSI board after to use powered down incorrectly. My issue was more with the pci-e bus. I had to reseat the CPU and let it sit for awhile without power plugged in. After putting everything back it powered fine with no issues.
But its odd that you you are having issues with your raid. Might just try breaking everything down and start with the basics.


I know lol I just have to re seat it and see from there, thanks man!

[MaadDaawg]

Personally, I think it's a RIVE issue. Had the same problem on mine :thumbdown:

[PhIlLy ChEeSe]

Personally, I think it's a RIVE issue. Had the same problem on mine :thumbdown:

What did you end up doing? Dumping it? I pulled the CPU and all connections, it is very dusty so i may wash it off.............or burn it. I may RMA the board then dump the cpu and use the mem fawk it all!

[MaadDaawg]

I have a 3960 processor and it still ran 3D benchs at 5.4 - 5.5ghz on SS. I tried to sell both but it didn't sell even at far less than I paid, so I'm thinking about putting into a gaming rig - have no idea yet how fast it will go on water :P

[PhIlLy ChEeSe]

I have a 3960 processor and it still ran 3D benchs at 5.4 - 5.5ghz on SS. I tried to sell both but it didn't sell even at far less than I paid, so I'm thinking about putting into a gaming rig - have no idea yet how fast it will go on water :P

Mine did 5.2 under water, have no other stuff to try it with. Well this board is RMA, Ive had it.

[Witchdoctor]

I have a 3960 processor and it still ran 3D benchs at 5.4 - 5.5ghz on SS. I tried to sell both but it didn't sell even at far less than I paid, so I'm thinking about putting into a gaming rig - have no idea yet how fast it will go on water :P

my 3930 does 4.8 24/7 and benches everything at 4.9
Got it off Duke, think he said it only did 5 or 5.1 cold so never benched it cold personally, bought specifically for a 24/7 platform.
Have to say I will never go back to 4 cores and look forward to the 8 core Hassy suposidly to be released third quarter next year and will be a Tick/shink from my understanding
So far the best gaming platform I have had to date, and with Crysis 3 actually utilizing the cores availible I have to think gaming is heading towards utilizing more cores

Sorry to hear about your board Philly :ohcrap:

That blows man

[GFDuke]

Yea Witchie 5.1 on SS. I never went LN2 with it. I don't think it would matter.

[Witchdoctor]

Still running strong bro ......... :thumbsup:

Did you call tek Philly ?

[PhIlLy ChEeSe]

Still running strong bro ......... :thumbsup:

Did you call tek Philly ?


Got an RMA in the mail, I was gonna reformat with another board then put my SSD'S back in and see but already had a number so.......
Your correct WD im playing BF3 on an Ivy bridge with two 580's, and its a world of difference compared to the SB-E. I'm not sure if its everything is so different but, I get stuttering when im being shoot? My 7970's never had a issue with the game, I may put them in this and see. I love BF3 but this set up makes me want to not even play no more.........Is there a BF3 patch for SLI micro stutter? I never had this issue before that I can recall, as I ran these cards prior to getting my 7970's. I was leaning towards getting rid of it, now I may keep it and sell my IB board. I got the AsRock Extreme 6 it seems OK, but nothing noticeable to speak of. Got the stock cooler on the 3570K :laughing:

Yeah if I can ever make it to Buffalo from here I may do some D ice runs to see what i can get out of it, just so much else going on right now.

[Witchdoctor]

yea I came from a 2600K , night and day, BF3 does well splitting the duty between cores, no patch I am aware of for SLI, but never had the issue and I ran 2x 580's prior to the Titans .... ?

yea for gaming more cores = smother game play.

[GFDuke]

I run a 3770K @ 4.6, a single ssd and one GTX680 @ stock and I have never gotten stutter. I really see no need for SLI playing BF3. Even Crysis plays smooth as hell on this setup. It sounds like you might want to change video card drivers.

[Witchdoctor]

yea that could be it,

I know FarCry 3 had some sli profiles availible

[PhIlLy ChEeSe]

I run a 3770K @ 4.6, a single ssd and one GTX680 @ stock and I have never gotten stutter. I really see no need for SLI playing BF3. Even Crysis plays smooth as hell on this setup. It sounds like you might want to change video card drivers.


I'm on my second driver's may try again, every time im in the game as soon as I get shoot it like delay reacts (the only way to explain it) like its lagging hard. I'll disable SLi see if it helps.

[PhIlLy ChEeSe]

OK so far I used the 4.11 from 2012 same effect also the newest Nvidia betta drivers no go, only thing i can think of that could be an issue(im sure there could be others). Is im putting the drivers on a separate HDD not on the SSD the OS is on, not sure if this is the cause? But my SSD only has so much room and I want to keep 10GB free fer wat not stuff.
Thoughts suggestions, opinions................ thanks all!

PS gonna get the latest approved drivers an try them on the same SSD. Unless I get a better suggestion.

[GFDuke]

I would think the drivers have to be installed on the Os drive. and they really are not that big to take up a lot of room. What size SSD are you running?

[PhIlLy ChEeSe]

I would think the drivers have to be installed on the Os drive. and they really are not that big to take up a lot of room. What size SSD are you running?


60GB damn BF3 takes up a lot of room

[PhIlLy ChEeSe]

Think I figured it out, though it has a new PSU running SLI GTX580 use 770W under heavy usage. My PSU TX750..............:blush:

[Witchdoctor]

Cool, so your just a power supply away from sucess :thumbsup:

I have one of these I can sell if intrested, ran 3930K @ 4.5 and 2x 580's Lightnings at 900 easily

http://www.newegg.com/Product/Product.aspx?Item=N82E16817256057

$ 105.00 shipped

[PhIlLy ChEeSe]

Cool, so your just a power supply away from sucess :thumbsup:

I have one of these I can sell if intrested, ran 3930K @ 4.5 and 2x 580's Lightnings at 900 easily

http://www.newegg.com/Product/Product.aspx?Item=N82E16817256057

$ 105.00 shipped


If I wasn't so broke I'd buy it!!! That's a good deal, I'm just gonna use one fer now. Hurting bad as far as money goes.................:blush:

[PhIlLy ChEeSe]

Well my mother board is on its way home, bad news they have the address wrong UGH FUCKING ASUS! JUNK! :thumbdown:

WORST CUSTOMER SERVICE EVAEVA!

[PhIlLy ChEeSe]

Had a bad feeling about sending it in, the lost my board ...................WTF!

[ThreeDhero]

I would tell them you want a board of equal or great value and youre being impacted daily by not having a PC. Or a full refund for the amount of the board sounds like bullshit to me man I'd bring the hammer down.

[PhIlLy ChEeSe]

I would tell them you want a board of equal or great value and youre being impacted daily by not having a PC. Or a full refund for the amount of the board sounds like bullshit to me man I'd bring the hammer down.


I was gonna, Fedex Guy called me looking for the right address IM A HAPPY MAN!!!:thumbsup:

[Witchdoctor]

Awsome, so you all set :)

[PhIlLy ChEeSe]

YUP YUP!

[OC Maximus]

nICE PSU Witchy!

Yummy... ;)

[PhIlLy ChEeSe]

Awsome, so you all set :)


Well, I thought I was till the northbridge fan was dead after I hooked it all up. Not unplugd but dead UGH!:thumbdown:

[Witchdoctor]

that blows dude, are they sending a new one ?

hate motherboard fans, they always F up

[PhIlLy ChEeSe]

that blows dude, are they sending a new one ?

hate motherboard fans, they always F up


I have yet to get a reply, it just blows!!! I'm thinking of just putting a fan over it.........

[GFDuke]

Did you try and pull the fan off the board for a sec and see if maybe it wasn't just hanging up/ Maybe its rubbing on something internally?

[PhIlLy ChEeSe]

Did you try and pull the fan off the board for a sec and see if maybe it wasn't just hanging up/ Maybe its rubbing on something internally?


I didn't remove it as its got a bunch of screws through the board, but it spins freely I tried a few times to jump it to see if it would work but nothing. At this rate, its gonna be two months without that computer.
I think the writing is on the wall here :thumbdown:, I have always had good service from them in the past!

[Witchdoctor]

I may be but that fan only runs when temps are calling it to run like the AsRock E11 ? But if you jumped it out with another power source I geuess that woulkd not come into play anyway :ohcrap:

what is the fan size

could you retro a 40MM of this VGA cooler

http://www.frozencpu.com/products/18496/vid-226/Titan_Universal_Active_Chipset_VGA_Copper_Heatsink _TTC-CUV1ABDIY.html?tl=g40c16s501#blank

[GFDuke]

I may be but that fan only runs when temps are calling it to run like the AsRock E11 ? But if you jumped it out with another power source I geuess that woulkd not come into play anyway :ohcrap:

what is the fan size

could you retro a 40MM of this VGA cooler

http://www.frozencpu.com/products/18496/vid-226/Titan_Universal_Active_Chipset_VGA_Copper_Heatsink _TTC-CUV1ABDIY.html?tl=g40c16s501#blank

IDK, but yea there might be a profile for it in the bios. That's a thought.

[Witchdoctor]

There it is, PCH control :thumbsup:

http://www.overclockaholics.com/forums/attachment.php?attachmentid=7050&stc=1&d=1374279089

[PhIlLy ChEeSe]

Here is there response, the fan worked fine when it left here " Thank you for your response. According to the repair history, the repair facility did not do anything to the north bridge. I would suggest trying to blow the dust out and check with the power connection with the fan on the unit. Please do let me know if the problem still persists."

ugh!

Thanks guys! I'll look in the bios, mine always was on before.

[PhIlLy ChEeSe]

There it is, PCH control :thumbsup:

http://www.overclockaholics.com/forums/attachment.php?attachmentid=7050&stc=1&d=1374279089

So I went and started to remove the fan assembly, NOT so easy as it is heat piped to every heat sink on it . So I only hand tightened the screws when I put them back. then went into the bios and adjusted the PCH as you out lined. BOOM working!!!!! :clapping:

[GFDuke]

Funny when we know more than the techs at the manufacturer.

[PhIlLy ChEeSe]

Funny when we know more than the techs at the manufacturer.


YUP YUP! :good:
I'm just grinning, now I can install everything!!!:clapping:

[PhIlLy ChEeSe]

OK,
No software tweaks, just felling out the bios. Yesterday I tried one of the preset overclocking settings in the bios(no boot). So this AM I went off my memory, not sure why the auto settings really power the voltage on the CPU I think it was around 1.53v witch is way out of whack! Still relearning here......trying to get my hunger back :thumbsup:

Nothing spectacular, just wanting to see if this setup is gimped or not as I'm not gonna build around it if it is. Bare in mind this is a fixed board and new memory(same as old stuff). So far so good, I will decrease room temps then good harder eventually...

http://www.3dmark.com/3dm11/6903813

[Witchdoctor]

Rock it Philly ..................... :thumbsup:

[Kal-EL]

Check!

[PhIlLy ChEeSe]

A lil betta 5.0 I remembered I have to go higher in the OS :thumbsup: Again no world record just seeing. one GPU score

@WD them TITANS CRASH IT !!!

http://www.3dmark.com/3dmv/4759164

[PhIlLy ChEeSe]

Just the CPU for now, I either borked something or I have a cold boot issue at minus 65 degrees, using a heat gun to try and wake her up now..............Kept crashing at 5300Mhz. Code was 101 that's power low right? Edit booting at 5300 now, minus 42

[Witchdoctor]

what you using dice or LN2

the sandies don't need extreme cold, just get max multi and that is typically the lid, as far as i understand it with Sandies

[PhIlLy ChEeSe]

what you using dice or LN2

the sandies don't need extreme cold, just get max multi and that is typically the lid, as far as i understand it with Sandies
Dice block cant vailidate im @5700

[PhIlLy ChEeSe]

it keeps defaulting to 3200?

[PhIlLy ChEeSe]

it keeps defaulting to 3200?

Well after break down, I found a bent CPU PIN :ohcrap: it went back with no issue

So today the UPS guy came by, 2 780 TI'S Beat IT!

http://www.youtube.com/watch?v=tiVxzKDWJqE

http://www.3dmark.com/3dm11/8113276

25929 in 3D mark 11:laughing: @4920Mhz

[Witchdoctor]

That memory is beastin bro, just need some core to go with it

Nice ......... :thumbsup:

[PhIlLy ChEeSe]

That memory is beastin bro, just need some core to go with it

Nice ......... :thumbsup:


Thanks man think I need more poweh, locking up around 4900Mhz now

[PhIlLy ChEeSe]

OK
So I found this thread on over volting the GTX 780 DC II @ kingpincooling
http://kingpincooling.com/forum/showthread.php?t=2346&page=2

But I need a little more help as it does not show how to use it in accordance with the RIVE board? I can solder in the 1K resistor, I think they said use the adjustable one? But they don't sow where it connects too? I just need someone to connect the dots for me.......................... Any help?
Thanks!

[PhIlLy ChEeSe]

guys
I'm thinking of setting up a Ram Disc, is it practical for my set up? I'm running Windows 7 64 bit, doing a re format. Gonna try to use the OverClock key see if I can get more out of these 780 TI's without having to hard mod them.
I read some where only advantage to a ram disc is for XP systems......

[Witchdoctor]

Not up on RAM Disk's

I think Duke had a set up a few years back for PCM05

He could probably shed some light on this

Freeze dem bitches :thumbsup:

[PhIlLy ChEeSe]

Freeze dem bitches :thumbsup:


LOL!
I know! Wanna get what i can out of them first, I got no issue blowing stuff up! But if I don't have to............
I got da blocks, but no time lately. Either way I wanna clock higher first then I'll lay into um

[Splave]

hey try forcing gen3 pci-e speed :) should boost a bit

[PhIlLy ChEeSe]

hey try forcing gen3 pci-e speed :) should boost a bit


Not sure what you mean, Forcing? exspand on that for me? Also I'm gonna mess with the Over Clock Key for the first time, supposedly I can overvolt the PGU'S with it. Any pointers?

I've always been set to Gen3 as far as I know.

[Witchdoctor]

gzGSqsidL30

http://www.techpowerup.com/downloads/2148/nvidia-geforce-kepler-pcie-3-0-mode-enabling-patch-for-sandy-bridge-e-systems/mirrors

[PhIlLy ChEeSe]

Thanks man!
Busy working, I will be cooling these GPU'S once I can flash them.................

[PhIlLy ChEeSe]

My system is locking up, after booting then trying to apply OC? Any advice? OK getting past that locking up, just need time to adjust some.....