Overclockaholics Forums - post error code 34 ?? MIVEz

Page 3 of 4

Show 40 post(s) from this thread on one page

Overclockaholics Forums (http://www.overclockaholics.com/forums/index.php)

- Overclockaholics Competitive Benchmark Team (http://www.overclockaholics.com/forums/forumdisplay.php?f=100)

- - post error code 34 ?? MIVEz (http://www.overclockaholics.com/forums/showthread.php?t=4967)

MaadDaawg

12-08-2011 06:15 AM

Quote:

Originally Posted by Patch (Post 87096)

34 is disabled PCIE switchy, GPU cold boot bug, no power to card (when I forget to plug it in) or simply poor contact. Vaseline won't cause your trouble - my slots always have giz. Look for some slimy eraser or an insulation crumb in the slot.

Most of the time I get that problem it's because the card is tilted down a little in the back from fiddling with something and the front of the card lifts up out of the slot a tad and loses contact.

I remove all eraser and insulation from the board last night, then tried compressed air from all angles to clean it out. Haven't tried it yet but hopefully that will do it. If not, either off to pep boys or I'll just try using rubbing alcohol.

DOM	12-08-2011 06:18 AM

Or just both and more scotch but I think u have a big supply in your home as it is haha

MaadDaawg

12-08-2011 07:17 AM

Quote:

Originally Posted by DOM (Post 87121)

Or just both and more scotch but I think u have a big supply in your home as it is haha

Actually, I am not a big drinker (unfortunately :rofl: ) I have several bottles of good single malt, and then a good bottle of other whiskey varieties for guests, even though we seldom have guests :laughing:

the bottle I described yesterday is half full (no, not half empty ;) ) and I've had it over a year.

So, still time to make your way to Chicago for some good sippin whiskey brothers :rofl:

MaadDaawg

12-08-2011 07:19 AM

Quote:

Originally Posted by Patch (Post 87096)

I thought of the tilted thingy because as you know the lightning with a fat boy is extremely heavy, and with board insulation, sometimes difficult to seat correctly.

but I ran startups with the air cooled card in every concievable position (well, except 69 of course :rofl: ) Even held it at different angles to no avail.

Maybe today :thumbsup:

MaadDaawg

12-08-2011 08:53 AM

tried it on the off chance...

debug goes through the boot up routine and gets up to
98 - console input devices connect
99 - Super IO Initialization

but when the monitor sets itself to the input I have the card on it drops back to

A2 - IDE Detect
34 - (32-36 = CPU post memory initialization)
AE - Legacy boot event

sometimes goes on to

AA - system has transitioned to AHPI mode
but windows never loads

any ideas?

off to pep boys soon

MaadDaawg

12-08-2011 10:23 AM

CRC

Eltra-Motive Cleaner

drying....

tba

GFDuke

12-08-2011 11:28 AM

All i can think of now is that maybe you tightened the pot down to hard and when it froze the board cracked or something to that effect. I honestly don't think it needs cleaning. But wth. Might as well try. Personally i think the board is fk'd. RMA time.

MaadDaawg

12-08-2011 12:31 PM

Quote:

Originally Posted by GFDuke (Post 87146)

I actually tightened the pot down less than I usually. Hope you're wrong, they just shipped my P67 today :argh:

I'll let ya know in a few hours

MaadDaawg

12-08-2011 02:07 PM

Think you pinned it Duke :thumbdown: but not positive.

At the beginning of the session, all was running pretty well, then after about 3 hours or so I started having problems, so I shut down and found the CPU waaay looser than I normally run it. So I tightened it down some more :dumbshit: on the frozen board.

Slot two still works fine but slot one keeps haning on 34 :thumbdown:

Patch

12-08-2011 02:26 PM

Don't waste time with RMA. Just use the other slot - it'll give you more room anyway.

Or bake it.

All times are GMT -10. The time now is 08:03 AM.

Page 3 of 4

Show 40 post(s) from this thread on one page