Overclockaholics Forums

Overclockaholics Forums (http://www.overclockaholics.com/forums/index.php)
-   Extreme Overclocking (http://www.overclockaholics.com/forums/forumdisplay.php?f=82)
-   -   Dat Fatboy Be HUMONGOUS (http://www.overclockaholics.com/forums/showthread.php?t=2653)

MaadDaawg 05-20-2010 12:47 PM

Dat Fatboy Be HUMONGOUS
 
Finally got my fatboy insulated and mounted to the card :) It's sitting in the slot but I can't run it yet cause I can't find my vaseline :ohcrap:

Ended up wrapping the entire pot with blue tape, then armalex (cut outs for the fittings etc), then a sheet of frost king all the way around too :eek: That did a pretty good job of eating up most of the gap but I erasered the fitting around the copper block then stuffed eraser into the sides and bottom and top after mounting the pot to the card.

Used 13 copper moffset blocks, 6 black aluminum chip sinks, and 7 low profile memory chip sinks.

Looks pretty bad ass :D As soon as I can find a black Sharpie so I can write MD on it I'll take a pic :thumbsup:

added: I broke my favorite insulating tool right at the end :ohcrap: my wooden chopstick snapped right in half dammit :D

Splave 05-20-2010 12:58 PM

in

!

Witchdoctor 05-20-2010 01:00 PM

LOL ...... No vaseline ???

sounds kinda Gay :laughing::laughing::laughing:

MaadDaawg 05-20-2010 01:04 PM

Come on Doc, everyone knows gays use lubricant, not vaseline.... jeeez :rofl:

Kal-EL 05-20-2010 01:26 PM

Thx for sharing, thread is epicless without pics :(

MaadDaawg 05-20-2010 01:49 PM

1 Attachment(s)
Ok, you're right (I guess).

But only 1 until I get MD stenciled on the front :D

Besides, it's a little lonely up there by itself :blink:

PS. no shop towels yet either

Splave 05-20-2010 05:50 PM

thats is looking shmexy bro

MaadDaawg 05-21-2010 02:21 AM

1 Attachment(s)
Thanks Splave :) I'll look better once I find a black marker to put the MD on the exposed frost king :D Off to the store today to buy some more vaseline and shop towels... then... ready to fire her up :muaha:

Here's a shot with her companion in crime :scared:

PS. I've noticed many of you have removed your RAM fans, I suspect that's because they have a tendency to pull vapors down onto the ram, and thus exposing the unused slots to possible condensate. I've taped over the empty slots and put eraser over the tape and against each side of the Ram sinks, so I'm thinkin I'll be ok ???

One of these days I'll try my RAM Pot by KP, but not this time ;)

MaadDaawg 05-21-2010 05:54 AM

Vaseline in hand... soon to be in slot.

New shop towel supply in house

countdown to begin soon :D

Kal-EL 05-21-2010 05:59 AM

Git er dun, start a new thread on your progress and post up them benchies ;)

Chuchnit 05-21-2010 06:05 AM

Quote:

Originally Posted by MaadDaawg (Post 41955)
Vaseline in hand... soon to be in slot.


:tg:




:wtfsign:

ReverendMaynard 05-21-2010 06:06 AM

Quote:

Originally Posted by MaadDaawg (Post 41955)
Vaseline in hand... soon to be in slot.

New shop towel supply in house

countdown to begin soon :D


In bold, plus the killer pics makes for epicness.

MaadDaawg 05-21-2010 07:03 AM

LOL

Vaseline actually in hand would be pretty disgusting huh? unless of course you were planning a date with your hand :ohcrap:

Correction, vaseline was in a tube, now small amount is in my #1 PCIe slot.
Switching to a new thread to track progress... more pics :D


All times are GMT -10. The time now is 10:02 AM.


Copyright ©2009 Overclockaholics.com