i7 ud5 oc - Page 2

Chicken Patty · #1 10-05-2009

Quote:

Originally Posted by skarface

whats vtt and nb??? im curiouse i wouldnt mind lowering my cpu some!

well I had some stability issues when I took the screen shot, and had the clocked lowered slightly from my 24/7 crunching settings. I am back up to 4.3 Ghz and slightly lower vcore. The issues I was having was the RAM. I just relaxed the timings a notch and its LinX stable now.

Here is CPU-Z and my voltages, hope this helps

everything here is right except for VTT. VTT is set at +75Mv and is 1.28v in windows. NB is at default 1.100v

punx223 · #2 10-05-2009

Quote:

Originally Posted by Chicken Patty

very similar to mine. I'm currently doing some tweaking on the voltage, but this is where I'm at now.

yes i need some serious help with voltages, my D0's both seem to need 1.36vcore for 200x20 without turbo.

skarface · #3 10-05-2009

Well i just got done playing crysis warhead all the way maxed out 1920x1200 around 70 fps without vsync and with vsync enabled never goes below 50 tops at 60! Looks great however when i installed the patches i was getting black blotches in lines and i was see through in certain areas of the game. The game unpatched ran great without any issues! So the way to install it as listed before works i had no issues even loaded faster imo!

Chicken Patty · #4 10-05-2009

Quote:

Originally Posted by skarface

Well i just got done playing crysis warhead all the way maxed out 1920x1200 around 70 fps without vsync and with vsync enabled never goes below 50 tops at 60! Looks great however when i installed the patches i was getting black blotches in lines and i was see through in certain areas of the game. The game unpatched ran great without any issues! So the way to install it as listed before works i had no issues even loaded faster imo!

Thanks for the feedback. what you sou check your FPS with, Fraps?

skarface · #5 10-05-2009

Quote:

Originally Posted by Chicken Patty

Thanks for the feedback. what you sou check your FPS with, Fraps?

I use evga precision and i have the g15 keyboard so i view temps, clocks and frames while in game on the keyboard!

@ punx tell him joe said hey aka skarface on the evga forums!

Chicken Patty · #6 10-05-2009

Quote:

Originally Posted by skarface

I use evga precision and i have the g15 keyboard so i view temps, clocks and frames while in game on the keyboard!

@ punx tell him joe said hey aka skarface on the evga forums!

ahh, my keyboard don't have a display so i'm fucked

punx223 · #7 10-05-2009

Quote:

Originally Posted by Chicken Patty

ahh, my keyboard don't have a display so i'm fucked

dude you can use the on screen display too

Chicken Patty · #8 10-05-2009

i got a patch and it worked.

However I just confirmed my 9800GX2 is dead. crashed after a few seconds of Crysis, and can't take furmark for more than a sec. or two. Thank god I had some 3870x2's laying around that are not mine. I'm installing drivers for it now and I'll post back.

skarface · #9 10-05-2009

Quote:

Originally Posted by Chicken Patty

i got a patch and it worked.

However I just confirmed my 9800GX2 is dead. crashed after a few seconds of Crysis, and can't take furmark for more than a sec. or two. Thank god I had some 3870x2's laying around that are not mine. I'm installing drivers for it now and I'll post back.

Hey i had some issues runng quad sli and what not but i found a pretty easy fix for gaming! U can try it! nvidia control panel>manage 3d settings> global tab scroll down to power managment mode and put it on performance instead of adaptive. In alot of my games during different video scenes the cards were downclocking because it was just a movie part of the game so they would downclock then upclock again when its time to play. In batman aa it was the worst they wouldnt upclock fast enough so the single gp that was clocked properly got shitted on with the full load causing low fps and driver crash. So performance will make it where anytime u open a 3d app all cores stay fully clocked untill the 3dapp is closed out

!!! In ur case since u have 2 gpus might be happening to the one as well where i had three cores downclocking.

Chicken Patty · #10 10-05-2009

alright, up and running. But now since it's an ATI card, EVGA Precision will not work. how can I view the FPS now? LOL.