[Neuromancer]

I have the N584, which from what I read (I forgot to check when I had the heatsink off a few minutes ago) infinieon chips.

Vgpu and vmem mods are what I was planning on. have not even run the cards at stock yet... when my board gets back (should be here thurs or friday... (thanks OC!!) I will be putting it back under water and playing around with all the cards before I get to modding them

Just ordered enough pots for all of them... with a couple extra.

Going to look at quick disconnect stuff for water cooling, so I can water cool the 7600s in SLI and hte 7800s in SLI.. plus I have a WB for the 4890, I want to take for a spin....


Oh that might be a future mod too... OCP for the EAH4890 IIRC the leds on the back of the card signified OCP shutoff when I was having problems at 1100 core before. Dunno if keeping the VRMs cooler will help prevent that or not. The FC waterblock I got for it, guy included half an old socketA hestsink to drop on the block over the VRMs said it helped keep temps down

[HITandRUN]

Mine has Samsung ram chips so these might OC nice. We'll see when I'm done with the other cards I have.

[Neuromancer]

Got tired of guessing and its only 4 screws... Infineon chips... ends in -14 so assume 1.4ns

Been a long time since I did the math... 2000/1.4 = ~1430 MHZ max stock volts?

[HITandRUN]

Originally Posted by Neuromancer

Got tired of guessing and its only 4 screws... Infineon chips... ends in -14 so assume 1.4ns

Been a long time since I did the math... 2000/1.4 = ~1430 MHZ max stock volts?

Same on this end just Samsung mem. We'll see.

BTW: Is this the mod you will be using?

[Neuromancer]

Originally Posted by HITandRUN

Same on this end just Samsung mem. We'll see.

BTW: Is this the mod you will be using?

No I have the 584 with infineon chips. Worse mem clocks but longer lasting RAM...thats for the original 7900GT's.

It's similar but OCP is said to be different (although they don't work apparently on the newer cards) the left OCP chip in that image is actually add a 100K in parallel (or pencil mod it to 47K) for switching frequency stability beyond 1.2volts.

http://www.xtremesystems.org/forums/...61&postcount=2 This post explains it.

vMem is the same i think but even with mod not expecting more than 900MHz due to the ICs.

Originally Posted by FACE411

I would just slap it over top of it and check it w/ the dmm.... The worst that can happen is it will not work.

Thanks will do that...

Curious though these mods are showing 10K 50K 100K variable resistors being added and what I measured on both 7600s and the 7900 the resistance ranges from .44 kOhm to .67kohm without power applied... (would not think it needs power applied for resistance maybe it does though).

[FACE]

Isn't the formula "measured resistance x20?" or something like that?

[Patch]

Originally Posted by Neuromancer

Curious though these mods are showing 10K 50K 100K variable resistors being added and what I measured on both 7600s and the 7900 the resistance ranges from .44 kOhm to .67kohm without power applied... (would not think it needs power applied for resistance maybe it does though).

Yes, measure resistance without power.

I had a couple EVGA 7600 GT's I tried to mod and bench a few months back, but the memory was super ultra crappy crap. So crappy, that a hefty GPU overclock was completely worthless. I'll see if I can find the mods.

[Neuromancer]

Originally Posted by FACE411

Isn't the formula "measured resistance x20?" or something like that?

If you have it set to 20KOhms yeah I think so... mine is auto ranging though so I thought should be straight up.

Originally Posted by Patch

Yes, measure resistance without power.

I had a couple EVGA 7600 GT's I tried to mod and bench a few months back, but the memory was super ultra crappy crap. So crappy, that a hefty GPU overclock was completely worthless. I'll see if I can find the mods.

yeah these ones have crap mem too.. DDR2 so not expecting a huge improvement without getting them up to speed. think I had almost NO overclock though with them at default voltages..



Poking around hte back of the N7600B rev 2.3 PCB (vmods I found are for 2.2) Im guessing hte read points are on the front of the card. I found 12v read points a HUGE amount of 5V read points...

The caps by the gpu core read 1.35v except the lowest one reads 1.25v,

Think I should give up on this crad. Not going to get me a lot of boints any way. Just move on to the good 7600gt KO, the 7800gts the 7900gt and the 9500Gt.

I got pictures of everything and when I am all done and everything works I will document them in the threads here.

One thread per card for easier reference.

Just measured the 7600KO and looks like the mod will be good and easy to do. Wish I have not wasted so much time on the rev 2.3 card.

Okay looks like this is going to take a little longer than I had hoped :(

Cant find my molex tool, my razors ARGH. I hate doing shit half-assed whne I do own the correct tool for the job. Going to tear everything apart get organized and start anew in a couple of hours. With a clean and tidy work space (at least until I start modding again).

Sucks trying to cram a living quarters, office, work shop and benching area into one room, but its only for a couple more months.

[Neuromancer]

Ugh was hoping to have at least some vmods done by now.. got home Tuesday and had to tear apart my RC car. Got it all back up and running. Got some household chores to do still no GPU put.. :( Thinking I will am going to pass on the 35L fill up this weekend and just save up for the 160L. Babysitting my sister's kids Fri/sat, so going to try and get some DIce in tonight though on CPU.

Will be first time frozen i7 run for me

Guessing Fri/sat night after the kids go to bed I can work on vmods.

EDIT: UGh just got the word gotta go get the DIce now if I am going.

BBL

[HITandRUN]

Originally Posted by Neuromancer

Ugh was hoping to have at least some vmods done by now.. got home Tuesday and had to tear apart my RC car. Got it all back up and running. Got some household chores to do still no GPU put.. :( Thinking I will am going to pass on the 35L fill up this weekend and just save up for the 160L. Babysitting my sister's kids Fri/sat, so going to try and get some DIce in tonight though on CPU.

Will be first time frozen i7 run for me

Guessing Fri/sat night after the kids go to bed I can work on vmods.

EDIT: UGh just got the word gotta go get the DIce now if I am going.

BBL

Nice! Looking forward to the numbers.