[DOM]

your 5mhz short of 5.6

but still nice mods/scores

[OC Maximus]

Thanks men

Spent more time on these 3 benches than I'd like to admit but sure learned a lot today

[Splave]

Originally Posted by DOM

not 1 but 3.... congrats on the triplets

was it on ln2 @ 0c ? multi ?

i hope i can blck mine up off the x55 or get x56 to boot past 5.6

so you taking her out so you can bench att night ?

x56 multi ln2 0c 1.68v 75% llc

Will see how high she will go today

http://valid.canardpc.com/show_oc.php?id=1758180

[ny_driver]

Originally Posted by OC Maximus

Back benching 3D @ 5.6GHz w00t!

Water Temps:
6c air blowing on rig
13c water loop temp at idle
15c water loop temp at full load
(CPU 1.65vcore, x2 vGpu 1.55v, vMem 1.75v)

3DMark2001 SE - 124309 marks - OC Maximus (OCAlliance) - (Ati Radeon HD 4870X2 @965/1000MHz) 4.8 + 29.1 points
3DMark03 - 128995 marks - OC Maximus (OCAlliance) - (Ati Radeon HD 4870X2 @950/1000MHz) 0.9 + 24.3 points
3DMark05 - 49140 marks - OC Maximus (OCAlliance) - (Ati Radeon HD 4870X2 @920/1000MHz) 4.9 + 24.2 points

That's pretty amazing you have the 2x gpu and the cpu in the loop and the water stays that cold. How hot does the cpu get fully loaded, and what waterblock are you using? I need to get a new top of the line block, like the EK supreme HF probably.

[Witchdoctor]

31K has been breached

Great work everyone............

[OC Maximus]

Originally Posted by ny_driver

That's pretty amazing you have the 2x gpu and the cpu in the loop and the water stays that cold. How hot does the cpu get fully loaded, and what waterblock are you using? I need to get a new top of the line block, like the EK supreme HF probably.

She sure knows how to take a load

CPU is not fully loaded since its 3D with no cpu test. I'll bench 06 today and see what water temp gets too. I do have one rad shoved in the a/c so its getting the coldest air forced through it. Three triple rads total so its a nice amount of water to take the heat load.

[ny_driver]

Originally Posted by OC Maximus

She sure knows how to take a load

CPU is not fully loaded since its 3D with no cpu test. I'll bench 06 today and see what water temp gets too. I do have one rad shoved in the a/c so its getting the coldest air forced through it. Three triple rads total so its a nice amount of water to take the heat load.

Hehehe.........

When I was using the A/C to chill my loop I only had a single rad 120 x 240mm. More water makes a big difference I'm sure, but I need the best block out there also.

Taking the block apart to check for any residual buildup from 2 days usewith a strainer/screen from a paint gun on it.......it's not cooling nearly as well as the night I first installed the stock base plate.

EDIT: I need to design my own base plate that won't get all filled with cat hair etc.....I have a couple nice big copper passive HS. I could make 1 base-plate out of each one. I'll have to get it machined square and flat with 6 holes.......probably be a failed experiment.

[OC Maximus]

Originally Posted by ny_driver

Hehehe.........

When I was using the A/C to chill my loop I only had a single rad 120 x 240mm. More water makes a big difference I'm sure, but I need the best block out there also.

Taking the block apart to check for any residual buildup from 2 days use.......it's not cooling nearly as well as the night I first installed the stock base plate.

Cat hair?

I'm using a Koolance CPU-360

[ny_driver]

......the hair gets everywhere, but I'm keeping my cats. The 360 looks real nice, but the EK supreme is slightly cheaper. Debating....might get an EK supreme LT if I can find one.

Hopefully I will be able to just strain out all the crap and keep using what I have.

EDIT: going to try adding a stretched stocking screen around the paintgun strainer in the reservoir, hopefully it'll still flow ok. The temps were very good the first night I reinstalled the cat-hair/lint free stock base plate.

I'd hate to have to remove the waterblock for cleaning daily.

EDIT: it still flows fine....

[Kal-EL]

Knock Knock on our brothers from Greece's Door